Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of HERAFLEX E 2517 1000 NT - TPC - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for HERAFLEX E 2517 1000 NT:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Heraflex E datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses
Any use of this information falls under the rules of our disclaimer.
Informations produit
TPC-ET Thermoplastic Elastomer. Lowest Modulus, Nominal Shore D/15s 22. Natural colour.
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 25 MPa ISO 527
Résistance au choc Charpy, +23°C N kJ/m² ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C N kJ/m² ISO 179/1eA
Contrainte à 10% de déformation 2 MPa ISO 527
Contrainte à 100% de déformation 5 MPa ISO 527
Contrainte à 300% de déformation 7 MPa ISO 527
Dureté Shore D 22 - ISO 7619-1
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fusion, 10°C/min 175 °C ISO 11357-1/-3
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Résistivité transversale 1E13 Ohm*m IEC 62631-3-1
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1090 kg/m³ ISO 1183
Caractéristiques
Transformation
Moulage par injection, Extrusion de profilés
Conditionnement
Grains, Couleurs naturelles
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Autres informations
Moulages par injection
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.05%. Typical conditions with a desiccant drier: temperature 110 ° C, dew point -30 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters
Melt TemperatureMold TemperatureInjection Speed
190 - 200°C 30 - 50°Cmedium
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.